Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Jacksonville?
Gate Installation services in Jacksonville typically cost between $2,800 and $9,500 for a complete project in 2026, including the gate, posts, hardware, and labor. A standard single-swing driveway gate on a prepared surface usually lands between $2,800 and $4,500, while a full automated slide gate with a motor, track, and concrete work runs $5,500 to $9,500 on average. Every project starts with a written price before any work begins, so the number you’re quoted is the number you pay.
Key Takeaways: Jacksonville Gate Installation Pricing
- Single swing gate (manual): $2,800 – $4,500
- Double swing gate (automated): $5,000 – $8,500
- Slide gate with motor and track: $5,500 – $9,500
- Pedestrian gate (standard 4-foot): $900 – $1,800
- Gate motor installation (existing gate): $1,200 – $2,600
- Most installations complete in 1 – 2 days
- Carver Gate Repair Jacksonville provides a written price before any work starts
Gate Installation Cost Breakdown (2026)
Here’s what Jacksonville homeowners can expect to pay for gate installation in 2026, broken down by gate type and scope. These ranges reflect actual project pricing we see across Duval County, from Arlington to Orange Park to the Beaches.
| Gate Type | Typical Cost Range | What’s Included |
|---|---|---|
| Single swing gate (manual) | $2,800 – $4,500 | Steel or aluminum gate, posts set in concrete, hinges, latch, full install |
| Single swing gate (automated) | $4,000 – $6,500 | Above, plus swing operator, keypad or remote, safety sensors |
| Double swing gate (manual) | $3,500 – $6,000 | Two gate leaves, heavy-duty posts, center latch or drop rod |
| Double swing gate (automated) | $5,000 – $8,500 | Two leaves, dual operators or single master/slave, safety edges, remotes |
| Slide gate with motor and track | $5,500 – $9,500 | Track or cantilever system, slide operator, concrete work, remotes |
| Pedestrian gate (standard 4-foot) | $900 – $1,800 | Single walk-through gate, posts, hardware, basic install |
| Gate motor only (existing gate) | $1,200 – $2,600 | Operator unit, mounting, wiring, programming, remotes |
These numbers assume a typical Jacksonville residential lot with reasonably level ground and standard access. What moves the price up or down? The biggest drivers are gate width (anything over 14 feet gets heavier fast), whether the site needs new concrete footings or a slide track, the type of motor (LiftMaster and FAAC swing operators cost more than a basic Mighty Mule arm, but they’re built for daily use), and whether existing posts can be reused. In Riverside and Avondale, where older homes sit on tighter lots, we often see custom-width gates needed to fit existing openings, which adds fabrication cost. In newer developments like Nocatee or Bartram Park, standard Driveway Gate widths keep pricing toward the lower end of these ranges.
What Affects Gate Installation Pricing in Jacksonville
- Gate material. Steel costs more than aluminum upfront but resists coastal corrosion better when properly powder-coated. Aluminum is lighter and well-suited to Florida humidity. Wrought iron, the classic Jacksonville look in San Marco and Springfield, sits at the top of the material range.
- Driveway width. A 10-foot single gate is straightforward. A 16-foot double gate needs two leaves, heavier posts, and a stronger operator. A 20-foot slide gate over in Mandarin means a longer track or a cantilever frame, which requires more steel and more concrete.
- Motor type and brand. A basic Linear or Ghost Controls operator runs less than a LiftMaster or FAAC. If the gate will cycle more than 15 times per day, the cheaper arm motors fail within a few years here. Salt air near Atlantic Beach and Mayport accelerates wear on exposed motor housings, so coastal installs typically justify a higher-grade unit.
- Site prep and drainage. Jacksonville’s sandy loam and high water table mean posts need proper depth (usually 36 to 48 inches) and concrete footings sized for the gate weight. Low-lying lots on the Westside may need additional gravel or drainage work so the gate path doesn’t wash out during summer storm season.
- Access and permitting. Gated driveway entrances in Jacksonville must maintain set-back distances from the street so vehicles don’t block the right-of-way while the gate opens. If the driveway apron needs adjustment to meet Duval County code, that adds concrete cutting or pour work to the bid.
- Automation features. Keypads, intercoms, vehicle loop detectors, battery backup for storm season, and smartphone control all add to the total. A loop detector alone is typically $400 – $700 installed, but it prevents the gate from closing on a car sitting in the path, which matters if the gate will run on a timer.
How to Save on Gate Installation
The most common way Jacksonville homeowners overspend is buying a motor that doesn’t match the gate weight. A $600 big-box swing arm bolted to a 900-pound gate fails inside a year, and then you’re paying for a motor replacement on top of the original install. Get the gate and operator sized correctly the first time.
Other practical savings:
- Reuse sound existing posts. If the current posts are plumb, set in concrete, and sized correctly, you may not need new ones. That removes $500 – $1,200 from the job.
- Choose manual over automated. An automated gate is convenient, but if you only open it twice a day, a manual swing gate with a quality latch saves $1,200 – $2,500 and runs for decades with minimal maintenance.
- Skip features you’ll never use. A keypad at the driveway and a couple of remotes covers most households. Intercoms and smartphone bridges add $300 – $900 each and sound better than they actually get used.
- Plan for a single visit. Having the concrete work, gate fabrication, motor mounting, and programming done by one crew prevents the hand-off gaps that come from coordinating three different contractors.
Carver Gate Repair Jacksonville gives a written price before any work starts, so you can compare the full scope against competitors with no risk of a moving number at the door. Estimates are free. Call (904) 490-8559 to set one up.
How the Gate Installation Process Works
Here’s the step-by-step process Carver Gate Repair Jacksonville follows on every gate installation, from first call to final walk-through.
- Initial call and site details. You call (904) 490-8559 and speak with a live person, 24/7. We gather the basics: gate location, approximate opening width, whether you want automation, and what’s currently there (fence, posts, nothing).
- On-site measurement and consultation. A background-checked, uniformed technician comes to the property, measures the opening, checks the ground, and discusses gate style, material, and motor options that fit your driveway and budget.
- Written price delivered. You receive a full written price for the entire project before any work is authorized. The number includes the gate, posts, motor (if applicable), concrete, hardware, and labor. Nothing is added at the door.
- Site preparation and post setting. The crew digs and sets posts in concrete at proper depth for Jacksonville’s sandy soil and water table, then lets the footings cure before hanging weight on them.
- Gate hanging and hardware installation. The gate is hung, hinges and latch are installed, and the gate is adjusted so it swings or slides cleanly without sagging.
- Motor mounting and programming (if automated). The operator is mounted, wired, and programmed. Remotes are synced, safety sensors and loops are installed and tested, and the open/close limits are set correctly.
- Final walk-through and written guarantee. We walk the gate through its full cycle with you, show you how to operate everything, and hand you a written guarantee covering the full installation for one year under the 365-Day Done Right Promise.
Gate Motor Brands We Install and Service
Carver Gate Repair Jacksonville technicians are trained on nine gate-motor brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters because installing a motor on a gate isn’t a universal job. A FAAC swing operator mounts and programs differently than a Viking slide operator. A technician who only knows one brand will tell you that brand is the only option. We match the right motor to the gate weight, the cycle frequency, and the coastal conditions of your specific property in Jacksonville.
Jacksonville-Specific Considerations for Gate Installation
Coastal Salt Air
Homes east of the Intracoastal, in Atlantic Beach, Neptune Beach, and Jacksonville Beach, deal with salt-corrosion pressure that inland properties don’t. Uncoated steel hardware, exposed motor housings, and standard-grade fasteners rust faster within a mile of the ocean. For these installs we recommend powder-coated aluminum gates or marine-grade steel with sealed hardware, and operators with sealed or protected control boards.
Hurricane Season and Gate Security
Jacksonville gets real wind. A gate acts as a sail during a named storm, and an improperly anchored post will loosen over repeated storm seasons. Posts for automated gates should be set at least 36 inches deep with proper concrete volume. For gates wider than 12 feet, we recommend a battery backup on the operator so the gate still functions during a power outage, which is common from June through November.
Setback Requirements
Driveway gates in Jacksonville must be positioned so a vehicle waiting at the gate doesn’t block the sidewalk or street. The city enforces setback rules through its permitting process. If your gate will open outward toward the street, the setback is even more critical. A gate that opens over a public sidewalk can create a pedestrian hazard. We account for setback compliance in every quote so the finished install passes inspection the first time. If you’re considering Gate Installation in Jacksonville, we can walk you through the setback math during the consultation.
Gate Installation vs. Gate Repair: Which Do You Need?
If your existing gate is structurally sound but the motor has failed, you don’t need a full installation. A motor replacement on a healthy gate runs $1,200 – $2,600 in Jacksonville, compared to $5,000 – $9,500 for a complete new automated gate. The decision usually comes down to three questions:
- Is the gate itself damaged, rusted through, or sagging? If yes, replace.
- Are the posts still plumb and solid in the ground? If they’re leaning or the concrete is cracked, a new install is the better long-term move.
- How old is the motor? If it’s over 10 years old and the gate is heavy, you’ll likely spend more keeping it alive than replacing the whole system.
We’ll give you an honest read on whether repair or replacement makes financial sense before you spend a dollar. That’s part of the written-price standard we’ve operated under since 2008.
FAQs – Gate Installation Cost in Jacksonville
How much does a driveway gate cost in Jacksonville, FL?
A manual single driveway gate in Jacksonville typically costs $2,800 – $4,500 installed. An automated single swing gate runs $4,000 – $6,500. Double automated gates start around $5,000 and can reach $8,500. Call (904) 490-8559 for a free written estimate specific to your property.
Is it cheaper to install a swing gate or a slide gate in Jacksonville?
A Pedestrian Gate or swing gate is generally $1,500 – $3,000 cheaper than a slide gate because slide gates require a track or cantilever frame, more concrete work, and a heavier-duty operator. But if your driveway slopes up from the street or lacks room for a gate to swing inward, a slide gate is the only practical option regardless of cost.
How long does gate installation take in Jacksonville?
Most residential gate installations complete in 1 – 2 days. Slide gate installations with new concrete work can take 2 – 3 days to allow for proper curing before the gate is hung and tested. We schedule a specific arrival window and confirm it before the crew shows up.
Can you install a gate on an existing fence?
Yes, in most cases. If the existing fence posts are set correctly and the fence structure is stable, we can hang a gate in the existing opening. The typical cost to add a gate to an existing fence runs $1,200 – $3,000 depending on gate width and whether you’re adding a motor.
Do I need a permit to install a gate in Jacksonville?
Most residential driveway gates that don’t exceed height limits and maintain proper setbacks can be installed under a minor permit or as part of an existing fence permit. Automated gates may require an electrical permit for the operator. We handle the permit paperwork and ensure the install meets Duval County code before we start digging. Call (904) 490-8559 and ask for details on your specific street.
Why Homeowners Choose Carver Gate Repair Jacksonville
Lonnie Burke leads the Carver Gate Repair Jacksonville team, and the standard here is simple: written prices, background-checked technicians, and a full-year guarantee on every installation. You don’t get a price that changes at the door. You don’t get a subcontractor who may or may not show up. You get a uniformed technician who calls ahead, arrives at the scheduled window, does the work, and cleans the site before leaving. That’s The Garrison Standard, and it’s been the operating rule since 2008.
If a repair we made fails within the first year, the second visit is free. No charge, no argument. That’s the 365-Day Done Right Promise, and it applies to every gate we install or repair in Jacksonville, the Beaches, and all of Duval County.
Get a Free Written Estimate in Jacksonville
If you’re ready to price a gate installation for your property, call (904) 490-8559. A live person answers, 24 hours a day, 7 days a week. We’ll schedule a site visit, take measurements, and deliver a written price before any work is authorized. You’ll know the exact number before you decide, and that number won’t move. Start with the home page to see the full scope of what we do, or call now to set up your free consultation.
Pricing reflects the Jacksonville market as of 2026. Carver Gate Repair Jacksonville offers free estimates – call (904) 490-8559.
Written by Lonnie Burke, Owner at Carver Gate Repair Jacksonville, serving Jacksonville since 2008.
What Our Customers Say
"Gate hinge was bending under the weight. Welded a new bracket on and re-hung it. Solid now."
- Rudy A."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P.